All posts by admin

IMG_1756

Wrist Pin Nightmare

1978 CB400T Hawk with siezed engine.

 

Wrist pins were locked up solid to the connecting rod. Only one option, cut the damn pistons off.

 IMG_1748

The first asshole tried using an air hammer to push them out, and mushroomed the pin to the rod.

IMG_1749

 

IMG_1750

 Cut the pins down as much as possible.

IMG_1754

Hillbilly clamp press

IMG_1755

 1 hour later,

IMG_1756

Rod ends look like shit now. Hopefully I can reem them out and get a decent surface back.

Cleaned it up with a little oven cleaner.

IMG_1757

Could have been worse I guess.

CB125 Street Tracker

CB125 Street Tracker build Part 1

Picked up a stock 1975 CB125 with low compression and a junk front end.

IMG_0854
Stock, unmolested CB125

IMG_0853

I decided to build a street tracker with the stock 125 engine modifed as much as safely possible.

Sourced this145CC cylinder and piston kit for a cb145, which is a euro version i guess? Bored cases to accept the bigger cylinder and it worked out perfect.

Next was the head, I used the head from an 86-87 ATC200X, milled .080″. This is too much! I had to cut a lot of material from the head and the piston for clearance.

In order to use the stock ignition system, you have to cut the end of the camshaft off. You want to cut the cam where the machined groove is,about 3/8″ from the end, cam chain side. Then you can assemble it like it was still stock.

Ordered this chinese knock off of an XR200 carb with throttle cable and K&N filter, and changed the main jet to a 75.

IMG_1664
CB125 ATC200X ( xr200 ) Head and Carburetor

I ditched the stock muffler and went with an Emgo ,
type but it iwas made for a larger diameter head pipe, so I welded a piece of 1-1/4″ pipe to it so I could get the larger diameter needed.

IMG_1727              IMG_1728

More to come.

CB125 Street Tracker
CB125 Street Tracker build

 

ST90 Lifan engine swap

1975 ST90 with the weak stock engine.

 

as we picked it up
as we picked it up

 

A 4-speed manual clutch with the provisions for an oil cooler was purchased from ebay smilar to this 125cc Lifan

The ST90 engine mounts to the frame with 4 bolts, instead of the usual 3 bolts that the other Honda horizontal engines mount with (CT70,XR50).

 

IMG_1251

The lower rear bolt holes can be used with a spacer, I made brackets that bolt to the engine with a hole to match the frames stock mounting hole.

 

IMG_1676

 

Exhaust is a custom bent 1-1/4″ Stainless steel header matched to a ZZZ muffler.

IMG_1678 IMG_1689

Position of the oil cooler is a bit of a problem. The best and cleanest location is to mount it directly in front of the head using stand offs. We welded 7mm X 1.0 thread nuts to one side ofa 3/8″ tube, and an M6 nut to the other, and simply bolted the cooler to it.

IMG_1731  IMG_1732

 

more to come

 

Restoring a vintage seat using Gojo hand cleaner

mms95img-1610403194

I bought a vintage 1965 Mustang bench seat for my 1968 F100 project. Seat had been sitting for 20 years or so in a guys attic.

IMG_1439 IMG_1440

I had heard about using hand cleaner and a brush so I gave it a shot.

I decided to use the GOJO 1109 Original Hand Cleaner. 14 oz.
and a cheap scrubbing brush Turtle Wax Interior Brush

It is as simple as it sounds. Put the Gojo on by hand and work in with the brush. Putting it on with the brush wastes more so just use your hand.

IMG_1443

Here is a shot of what looks like tar build up on the top of the seat.

After you scrub it down, rinse it with a rag and some water. You can use a garden hose if the seat isnt ripped up.

After rinsing it off, I used Lexol Leather Conditioner

IMG_1447

Seat looks almost as good as new.

Some things to note. The vinyl on this seat was pretty old and brittle in some places. In most cases as soon as I put the Gojo on it somewhat seamed to soften. If the material had already hardened it didnt seam to soften it much.

PW 50 Restoration

 IMG_1595

Picked up a beat Yamaha PW50 for a couple hundred bucks off craigslist. Everything was trashed and needed painted at the least.

IMG_1565 IMG_1564 IMG_1563 IMG_1562

I picked up this cheap complete top end kit with new head, cylinder, and piston, for less than price of factory gaskets.

I also decided to go with these brand new set of front fork tubes instead of reubuilding the stock pieces.

At this point you will have a brand new bike for a fraction of the cost. New plasticis available if yours is in bad shape, I chose to sticker up the factory plastic to keep the cost down.

 

PW50 Finished
PW50 Finished

Club Car engine swap Part 3, manual choke and fuel line install

See Part 2

With the engine configured to use the factory governor system, it is necessary to implement a manual choke. The stock system has the throttle in the wide open posistion at start, then the engine speed pushes it closed once it starts. Because of this, there isnt a strong enough vacuum signal across the main jet to pull fuel into the carb body, so a choke is required.

I purchased a push mower universal throttle cable kit. The kit I used comes with several different levers to use, I modifed one of them to use as the termination at the carburetor.

IMG_1461

Simply cut the cable to length and bend a “Z” at the end using 2 needle nose pliers. I put a small hole into the stock choke lever and inserted the Z into that.

IMG_1457     IMG_1456 IMG_1458

For the fuel line:

Geoff at Vegas Carts recomends using the spacer between the carb and head to source the vacuum for the fuel pump. I tapped it to 1/8″ npt, and used a 1/8″ npt x 3/16″ barbed tube elbow. Using this location will generate too much pressure from the pump, so a “relief” line needs to be installed. I didnt want it to relieve all the fuel pressure so I used a reducing tee to reduce the 3/16″ tube down to 1/8″ for the return. I then used a bored thru tube compression fitting and installed the relief tube into the tank.

IMG_1460  IMG_1455

I do not like the location that I put the relief line in the tank. If i was to do it again I would put it lower in the tank to keep air out of the line.

Club Car engine swap Part 2, Header and throttle

See Part 1

Throttle:

Take the engines old throttle lever off, take the first section of the golf carts throttle cable, the one that ran from switch box to the rearends speed control, and connect it to the engines governor spring. Use the engines existing cable clamp to hold the golf cart throttle cable down. This is in the weaker part of the cable so use care when tightening.

IMG_1411 IMG_1412

This worked perfect! You can be easy on the throttle and just creep around, or nail it and it takes off wide open, and then the governor kicks in like normal.

The engines choke will need to be utilized for smooth starting. You could possibly use the factory airbox and “choke”, I havent decided which route to head.

Exhaust:

I cut out a flange of 3/16″ plate and custom bent the 1-1/4″ tube.

IMG_1408

We bent it 180 degrees to send it back under the engine

IMG_1410

Then a couple 45 degree bends to send it out the rear

IMG_1421

Muffler/silencer and tail pipe are still in the works

Club Car engine swap Part 1

Started with a 440CC GX390 clone from Vegas Carts, and the tapered adapter to retain the factory clutch. The engine comes with SST valves and stiffer valve springs, 20HP out of the box for $399 to the door. It arrives without the head bolted on, and the standard steel valves and weaker springs in place. The stainless valves and stiffer springs are shipped seperate. I saved the stainless steel valves for my GX390 alcohol burning race kart engine.

After trimming the factory crankshaft for use with the adapter, to retain the factory clutch and variator, next is a mount to adapt to the engine to cradle.

The Vegas 440cc does not have the same base bolt pattern as a Honda GX390 or clone. All you need to do is raise the engine 2″ to get the crankshaft to the original position. I did this by welding 2 pieces of 2″x2″x3/16″ angle with a plate between them. I put slots in the plate (new engine side) running parrallel with the crankshaft. The cradle has slots in it from the factory running the oter direction, so you can just put holes in the lower side of the mount, this will give you plenty of adjustment. For this model cart you want 9-5/8″ from crank centerline, to the centerline of drven pulley on the axle.

Next are the brackets to mount the factory starter generator. The GX engine typically has a fuel tank mounted on top, Vegas engine is a little different and  made mounting much easier. We used some flat plate bent with a hammer in a vice. We were able to use the factory adjustment plate with the slot so that made it that much easier.

IMG_1344

IMG_1346     IMG_1345

PArt 2 : Throttle and Exhaust